ELEC60013-ES-CW2/lib/es_can/es_can.cpp

#include <es_can>
#include <stm32l4xx_hal_can.h>
#include <stm32l4xx_hal_cortex.h>
#include <stm32l4xx_hal_gpio.h>
#include <stm32l4xx_hal_rcc.h>

// Overwrite the weak default IRQ Handlers and callabcks
extern "C" void CAN1_RX0_IRQHandler(void);
extern "C" void CAN1_TX_IRQHandler(void);

// Pointer to user ISRS
void (*CAN_RX_ISR)() = NULL;
void (*CAN_TX_ISR)() = NULL;

// CAN handle struct with initialisation parameters
// Timing from http://www.bittiming.can-wiki.info/ with bit rate = 125kHz and clock frequency = 80MHz
CAN_HandleTypeDef CAN_Handle = {
	CAN1,
	{
		40,				 // Prescaler
		CAN_MODE_NORMAL, // Normal/loopback/silent mode
		CAN_SJW_2TQ,	 // SyncJumpWidth
		CAN_BS1_13TQ,	 // TimeSeg1
		CAN_BS2_2TQ,	 // TimeSeg2
		DISABLE,		 // TimeTriggeredMode
		DISABLE,		 // AutoBusOff
		ENABLE,			 // AutoWakeUp
		ENABLE,			 // AutoRetransmission
		DISABLE,		 // ReceiveFifoLocked
		ENABLE			 // TransmitFifoPriority
	},
	HAL_CAN_STATE_RESET, // State
	HAL_CAN_ERROR_NONE	 // Error Code
};

// Initialise CAN dependencies: GPIO and clock
void HAL_CAN_MspInit(CAN_HandleTypeDef *CAN_Handle) {

	// Set up the pin initialisation
	GPIO_InitTypeDef GPIO_InitCAN_TX = {
		GPIO_PIN_12,			// PA12 is CAN TX
		GPIO_MODE_AF_PP,		// Alternate function, push-pull driver
		GPIO_NOPULL,			// No pull-up
		GPIO_SPEED_FREQ_MEDIUM, // Medium slew rate
		GPIO_AF9_CAN1			// Alternate function is CAN
	};

	GPIO_InitTypeDef GPIO_InitCAN_RX = {
		GPIO_PIN_11,			// PA11 is CAN RX
		GPIO_MODE_AF_PP,		// Alternate function, push-pull driver
		GPIO_PULLUP,			// Pull-up enabled
		GPIO_SPEED_FREQ_MEDIUM, // Medium slew rate
		GPIO_AF9_CAN1			// Alternate function is CAN
	};

	// Enable the CAN and GPIO clocks
	__HAL_RCC_CAN1_CLK_ENABLE();  // Enable the CAN interface clock
	__HAL_RCC_GPIOA_CLK_ENABLE(); // Enable the clock for the CAN GPIOs

	// Initialise the pins
	HAL_GPIO_Init(GPIOA, &GPIO_InitCAN_TX); // Configure CAN pin
	HAL_GPIO_Init(GPIOA, &GPIO_InitCAN_RX); // Configure CAN pin
}

uint32_t CAN_Init(bool loopback) {
	if (loopback)
		CAN_Handle.Init.Mode = CAN_MODE_LOOPBACK;
	return (uint32_t)HAL_CAN_Init(&CAN_Handle);
}

uint32_t setCANFilter(uint32_t filterID, uint32_t maskID, uint32_t filterBank) {

	// Set up the filter definition
	CAN_FilterTypeDef filterInfo = {
		(filterID << 5) & 0xffe0, // Filter ID
		0,						  // Filter ID LSBs = 0
		(maskID << 5) & 0xffe0,	  // Mask MSBs
		0,						  // Mask LSBs = 0
		0,						  // FIFO selection
		filterBank & 0xf,		  // Filter bank selection
		CAN_FILTERMODE_IDMASK,	  // Mask mode
		CAN_FILTERSCALE_32BIT,	  // 32 bit IDs
		CAN_FILTER_ENABLE,		  // Enable filter
		0						  // uint32_t SlaveStartFilterBank
	};

	return (uint32_t)HAL_CAN_ConfigFilter(&CAN_Handle, &filterInfo);
}

uint32_t CAN_Start() {
	return (uint32_t)HAL_CAN_Start(&CAN_Handle);
}

uint32_t CAN_TX(uint32_t ID, uint8_t data[8]) {

	// Set up the message header
	CAN_TxHeaderTypeDef txHeader = {
		ID & 0x7ff,	  // Standard ID
		0,			  // Ext ID = 0
		CAN_ID_STD,	  // Use Standard ID
		CAN_RTR_DATA, // Data Frame
		8,			  // Send 8 bytes
		DISABLE		  // No time triggered mode
	};

	// Wait for free mailbox
	while (!HAL_CAN_GetTxMailboxesFreeLevel(&CAN_Handle))
		;

	// Start the transmission
	return (uint32_t)HAL_CAN_AddTxMessage(&CAN_Handle, &txHeader, data, NULL);
}

uint32_t CAN_CheckRXLevel() {
	return HAL_CAN_GetRxFifoFillLevel(&CAN_Handle, 0);
}

uint32_t CAN_RX(uint32_t &ID, uint8_t data[8]) {
	CAN_RxHeaderTypeDef rxHeader;

	// Wait for message in FIFO
	while (!HAL_CAN_GetRxFifoFillLevel(&CAN_Handle, 0))
		;

	// Get the message from the FIFO
	uint32_t result = (uint32_t)HAL_CAN_GetRxMessage(&CAN_Handle, 0, &rxHeader, data);

	// Store the ID from the header
	ID = rxHeader.StdId;

	return result;
}

uint32_t CAN_RegisterRX_ISR(void (&callback)()) {
	// Store pointer to user ISR
	CAN_RX_ISR = &callback;

	// Enable message received interrupt in HAL
	uint32_t status = (uint32_t)HAL_CAN_ActivateNotification(&CAN_Handle, CAN_IT_RX_FIFO0_MSG_PENDING);

	// Switch on the interrupt
	HAL_NVIC_SetPriority(CAN1_RX0_IRQn, 6, 0);
	HAL_NVIC_EnableIRQ(CAN1_RX0_IRQn);

	return status;
}

uint32_t CAN_RegisterTX_ISR(void (&callback)()) {
	// Store pointer to user ISR
	CAN_TX_ISR = &callback;

	// Enable message received interrupt in HAL
	uint32_t status = (uint32_t)HAL_CAN_ActivateNotification(&CAN_Handle, CAN_IT_TX_MAILBOX_EMPTY);

	// Switch on the interrupt
	HAL_NVIC_SetPriority(CAN1_TX_IRQn, 6, 0);
	HAL_NVIC_EnableIRQ(CAN1_TX_IRQn);

	return status;
}

void HAL_CAN_RxFifo0MsgPendingCallback(CAN_HandleTypeDef *hcan) {

	// Call the user ISR if it has been registered
	if (CAN_RX_ISR)
		CAN_RX_ISR();
}

void HAL_CAN_TxMailbox0CompleteCallback(CAN_HandleTypeDef *hcan) {

	// Call the user ISR if it has been registered
	if (CAN_TX_ISR)
		CAN_TX_ISR();
}

void HAL_CAN_TxMailbox1CompleteCallback(CAN_HandleTypeDef *hcan) {

	// Call the user ISR if it has been registered
	if (CAN_TX_ISR)
		CAN_TX_ISR();
}

void HAL_CAN_TxMailbox2CompleteCallback(CAN_HandleTypeDef *hcan) {

	// Call the user ISR if it has been registered
	if (CAN_TX_ISR)
		CAN_TX_ISR();
}

// This is the base ISR at the interrupt vector
void CAN1_RX0_IRQHandler(void) {

	// Use the HAL interrupt handler
	HAL_CAN_IRQHandler(&CAN_Handle);
}

// This is the base ISR at the interrupt vector
void CAN1_TX_IRQHandler(void) {

	// Use the HAL interrupt handler
	HAL_CAN_IRQHandler(&CAN_Handle);
}