mirror of
https://github.com/supleed2/ELEC50010-IAC-CW.git
synced 2024-11-10 01:35:49 +00:00
80 lines
2.5 KiB
Systemverilog
80 lines
2.5 KiB
Systemverilog
module mips_cpu_bus_tb;
|
|
|
|
parameter INSTR_INIT_FILE = "";
|
|
parameter DATA_INIT_FILE = "";
|
|
parameter TIMEOUT_CYCLES = 100; // Timeout cycles are higher to account for memory stall delays
|
|
|
|
logic clk, reset, active, write, read, waitrequest;
|
|
logic[31:0] address, register_v0, writedata, readdata;
|
|
logic[3:0] byteenable;
|
|
|
|
mips_cpu_bus_memory #(INSTR_INIT_FILE, DATA_INIT_FILE) memInst( //Avalon memory mapped bus controller (slave)
|
|
.clk(clk), // clk input to mem
|
|
.reset(reset), // reset input to stall mem during cpu reset
|
|
.address(address), // addr input to mem
|
|
.write(write), // write flag input
|
|
.read(read), // read flag input
|
|
.waitrequest(waitrequest), // mem stall output
|
|
.writedata(writedata), // data to be written
|
|
.byteenable(byteenable), // byteenable bus for writes
|
|
.readdata(readdata) // read output port
|
|
);
|
|
|
|
mips_cpu_bus cpuInst(
|
|
.clk(clk), // clk input to cpu wrapper
|
|
.reset(reset), // reset input
|
|
.active(active), // active output flag
|
|
.register_v0(register_v0), // debug $2 or $v0 output bus
|
|
.address(address), // mem addr output
|
|
.write(write), // mem write output flag
|
|
.read(read), // mem read output flag
|
|
.waitrequest(waitrequest), // mem stall input flag
|
|
.writedata(writedata), // data to write to mem output
|
|
.byteenable(byteenable), // bytes to write output
|
|
.readdata(readdata) // data from mem input
|
|
);
|
|
|
|
// Setup and clock
|
|
initial begin
|
|
$dumpfile("mips_cpu_bus.vcd");
|
|
$dumpvars(0,mips_cpu_bus_tb);
|
|
clk=0;
|
|
|
|
repeat (TIMEOUT_CYCLES) begin
|
|
#10;
|
|
clk = !clk;
|
|
#10;
|
|
clk = !clk;
|
|
end
|
|
|
|
$fatal(2, "Simulation did not finish within %d cycles.", TIMEOUT_CYCLES);
|
|
end
|
|
|
|
initial begin
|
|
reset <= 1;
|
|
@(posedge clk);
|
|
reset <= 0;
|
|
|
|
@(posedge clk);
|
|
assert(active==1)
|
|
else $display("TB : CPU did not set active=1 after reset.");
|
|
|
|
while (active) begin
|
|
//$display("Clk: %d", clk);
|
|
@(posedge clk);
|
|
//$display("Register v0: %d", register_v0);
|
|
//$display("Reg File Write data: %d", cpuInst.in_writedata);
|
|
$display("Reg File Out Read data: %h", cpuInst.mips_cpu_harvard.out_readdata1);
|
|
$display("Reg File opcode: %b", cpuInst.mips_cpu_harvard.regfile.opcode);
|
|
//$display("ALU output: %h", cpuInst.out_ALURes);
|
|
//$display("ALU input B: %h", cpuInst.alu.B);
|
|
end
|
|
|
|
@(posedge clk);
|
|
$display("TB: CPU Halt; active=0");
|
|
$display("Output:");
|
|
$display("%d",register_v0);
|
|
$finish;
|
|
end
|
|
|
|
endmodule |